Infrasound sensors
MB3a
The MB3a is an infrasound sensor developed by the CEA, following the MB2000 and MB2005 series, which allows the recording of very-low-frequency acoustic signals over a broad frequency band, with an excellent resolution and a large dynamic range.
The MB3 is remarkable for an extremely low level of instrumental noise (<-80 dB.Pa / √ Hz @ 1 Hz) allowing the sensor to resolve more than 18 dB the Low Noise Model. This sensor has been designed especially to meet the requirements of infrasound stations of the IMS network (International Monitoring System) installed as part of the CTBT (Comprehensive nuclear Test Ban Treaty).
Accessories
Cables
MB3a/MB3d power cable
3 pin Fischer connector to fast on plug, 2 wires, 1.5 mm², Ø 9.3 mm
Standard length : 3 meters
Signal cable
18 pin Fischer connector to not wired, 18 wires AWG24 Ø 8.48 mm shielded.
Standard lenght : 3 meters
Magnet adjustment cable
18 pin Fischer connector to banana plugs designed to adjust the magnet position (multimeter required).
Tools
Magnet adjustment cable
18 pin Fischer connector to banana plugs designed to adjust the magnet position (multimeter required).
Magnet Wrench
Specific wrench designed to adjust the magnet position.
Packaging
Screwpack
Plastic packaging for one Mb3a or Mb3d, protected into specific foams.
Not watertight, crush-proof and dust-proof, water, oil-projection and humidity resistant.
Weight : 0.4 Kg
Carton box
Carton box specially designed for MB3a and MB3d transportation.
Pelicase 1650 (6 sensors)
Pelicase 1650 with adapted foam specificly designed to carry 6 MB3a and cables. Equipped with one telescopic handle and 2 wheels.
Dimensions : 724 x 441 x 267 mm
Weight : 13.47 Kg
Pelicase 1430 (1-2 sensors)
Pelicase 1430 with adapted foams available in 1 sensor or 2 sensors (MB3a or MB3d).
Dimensions : 345 x 146 x 297 mm
Weight : 2.59 Kg
Battery
Battery Yuasa
12V BATTERY
12Ah /12V Lead Acid
97.5 X 98 X 151 mm / 4kg
Quick Connect
Charge Current Max: 3A
Cyclic Charge Voltage
Max:15V
Datasheet : NP_SERIES_BROCHURE_NP12-12
Interconnection boxes
Interconnection boxes
MB3d
MB3d sensors is the digital version of the MB3a. Recommended for short-term measurements, it encapsulates a low-noise 24 bit digitizer (ADC), with a calibration board, a time card and a storage capacity of 1 Go.
Accessories
Cables
MB3a/MB3d power cable
3 pin Fischer connector to fast on plug, 2 wires, 1.5 mm², Ø 9.3 mm
Standard length : 3 meters
MB3d serial cable
18 pin Fischer connector to DB9, connector 3 wires AWG24 shielded.
standard length : 3 meters
PC/USB cable
18 pin Fischer connector to USB
4 wires AWG25 shielded.
Standard length : 1.5 or 3 meters
GPS cable
Coaxial TNC to TNC
KG58C/U 50 Ω PVC, Ø 4.93 mm shielded.
Standard length : 5 meters
Magnet adjustment cable
18 pin Fischer connector to banana plugs designed to adjust the magnet position (multimeter required).
Tools
RS232 to Ethernet converter for MB3d
The RS232 to Ethernet converter allows remote retrieval of your MB3d miniSEED files through secure FTP access.
GPS antenna PROCOM 2000B
Flat-pack GPS-antenna for fixed installations.
Full hemispherical coverage.
Built-in high gain, low noise amplifier.
Right-hand circular polarization (RHCP).
3 V or 5 V supply voltage.
DC supply via RF-connector.
EMC tested to IEC 801 and IEC 255.
Provided with TNC (female) connector.
ROHS compliant.
datasheet: gps-2000.en-GB
GPS cable
Coaxial TNC to TNC
KG58C/U 50 Ω PVC, Ø 4.93 mm shielded.
Standard length : 5 meters
TNC Male to TNC Male Right Angle Adapter
Right angle adapter to connect directly the GPS antenna PROCOM 2000B to the MB3d, without cable.
Magnet adjustment cable
18 pin Fischer connector to banana plugs designed to adjust the magnet position (multimeter required).
Magnet Wrench
Specific wrench designed to adjust the magnet position.
Packaging
Screwpack
Plastic packaging for one Mb3a or Mb3d, protected into specific foams.
Not watertight, crush-proof and dust-proof, water, oil-projection and humidity resistant.
Weight : 0.4 Kg
Carton box
Carton box specially designed for MB3a and MB3d transportation.
Pelicase 1650 (6 sensors)
Pelicase 1650 with adapted foam specificly designed to carry 6 MB3a and cables. Equipped with one telescopic handle and 2 wheels.
Dimensions : 724 x 441 x 267 mm
Weight : 13.47 Kg
Pelicase 1430 (1-2 sensors)
Pelicase 1430 with adapted foams available in 1 sensor or 2 sensors (MB3a or MB3d).
Dimensions : 345 x 146 x 297 mm
Weight : 2.59 Kg
Battery
Battery Yuasa
12V BATTERY
12Ah /12V Lead Acid
97.5 X 98 X 151 mm / 4kg
Quick Connect
Charge Current Max: 3A
Cyclic Charge Voltage
Max:15V
Datasheet : NP_SERIES_BROCHURE_NP12-12
SIS-1
SIS-1 is a rugged-field infrasound sensor, ideal for portable systems, remote sites, or in addition to a seismic station. With the small size and weight, SIS-1 is easily deployable and provides reliable infrasound signal over a wide frequency bandwith.
Accessories
MB3a PP - 2 PRESSURE OUTPUTS VERSION
Seismo Wave has developped a new version of the MB3a analog infrasound sensor in order to records high amplitude atmospheric events. The two pressure outputs are respectively set at 2mV/Pa and 20mV/Pa. At 2mV/Pa, the dynamic range of the pressure output reaches +/- 10 550 Pa.
Accessories
Cables
MB3a/MB3d power cable
3 pin Fischer connector to fast on plug, 2 wires, 1.5 mm², Ø 9.3 mm
Standard length : 3 meters
Signal cable
18 pin Fischer connector to not wired, 18 wires AWG24 Ø 8.48 mm shielded.
Standard lenght : 3 meters
Magnet adjustment cable
18 pin Fischer connector to banana plugs designed to adjust the magnet position (multimeter required).
Tools
Magnet adjustment cable
18 pin Fischer connector to banana plugs designed to adjust the magnet position (multimeter required).
Magnet Wrench
Specific wrench designed to adjust the magnet position.
Packaging
Screwpack
Plastic packaging for one Mb3a or Mb3d, protected into specific foams.
Not watertight, crush-proof and dust-proof, water, oil-projection and humidity resistant.
Weight : 0.4 Kg
Carton box
Carton box specially designed for MB3a and MB3d transportation.